Subaru Won't Start After Timing Belt Replacement
If your car has issues starting and then runs rough, issues with ignition are usually related to either fuel, air or spark. Start date jun 6, 2008;
Joined jun 6, 2008 location tacoma, wa tdi 2002 jetta jun 6, 2008 #1 i have a 2002 jetta tdi with 108k that broke a timing belt and the resultant mess with bent valves and etc.
Subaru won't start after timing belt replacement. And sport for a haynes manual, the pics of the sprockets are best you will find. Will not start after timing belt change. It cranks and tries to sputter and start but just wont do it.
I ordered up a kit from jackie at annapolis subaru (great service and prices), got the factory service manual and got to work. The number one leading cause of a no start after major engine work, or timing belt replacement is the timing it off. The rodent damage can usually be seen quickly by looking into the engine compartment.
Ok, so i was due for a timing belt replacement. I have checked the timing over and over and find all the marks lining up every time. Had the timing belt replaced at a shop once and the car was returned to me running rough, the mechanic said it was due to the ecu needing to adjust but actually they had replaced the spark plugs in the wrong order.
Unfortunately that is the most likely outcome of a timing belt breaking on a 97+ subaru engine. And the throttle is wide open. I have a 2001 honda civic ex with 110,000 miles.
After replacing the timing belt, water pump, cam and crank seals, valve cover gaskets the car wont start. I didn't try turning the crank, so i'll give that a try after checking the timing again one mote time tonight. After swapping them to the correct order the car ran great, just something to check before jumping to the bent valves assumption.
He replaced the timing idler gear (think that's what it was called) because it had seized up. Rodent damage can be another reason why your subaru outback won’t start. Before trying to start the engine, i bumped it a few times to center the timing belt on the gears.
I have seen a few folks (i own a auto repair shop) that have used the wrong mark on the crank cog, use the line , not the arrow, the arrow should point to the drivers side. After putting everything back together, i turned the key, and the car wouldn’t start. And lastly, the tdc used for timing belt replacement is not the acual tdc.
We just replaced the timing belt on a subaru legacy and it won''t start now. Put everything together, after checking timing belt alignment multiple times, and now it wont start. Ok, my timing belt broke, (1996 subaru outback legacy) i replaced the belt and dialed in the timing marks.
He has checked the fuel. This is most always the cause of a no start after a diy timing belt job. Any help would be appreciated.
Aux belt came adrift and jammed in crank pulley, crank pulley jammed and timing belt snapped. Last weekend i decided to change the timing belt. I had a mechanic very familiar with the old.
Won't start after timing belt replacement. The engine turned over and it stuttered for a second while i turned the key, but it died as soon as i. He set the timing, but the car won't start.
The timing belt was replaced, but the car still won't start. Verify the timing one more time and then run a compression test to narrow down which cylinders are effected, it's possible that only a few valves were damaged after the break. Removed head and replaced valve and guide by specialist.
The animals crawl under the vehicle and bite through cables and wires. These timing marks are a bitch, sport for a good paint marker and mark everything first! The timing was set with the marks on the belt and on the engine front.
Car does not start after timing belt chain replacementif your car does not start after timing chain or belt replacement, or the car does not start after engi. Yes, the video is unedited. Either from using the wrong marks or the belt is just a couple of teeth off by accident.
I have checked for spark from all plugs, wires and coil packs but they are ok. He also replaced the timing belt. It cranks, and sounds normal while cranking, but doesn't even try to fire up.
I checked vcds, and the engine is throwing no codes. I own the honda service manual for this car, and i followed the instructions exactly. Then, there is plenty of info out there to try and diagnose why your car won’t start/run properly.
This is very common with first timers but it. Apologies in advance for the extremely long video. On trying to start, it just cranked and would not start.
Had to replace water pump on1997 subaru impresa with 2.2 liter, putting on new timing belt (several times),but it wont start and sounds like i have no compression,alligned all timing marks. Crank arrow at 12:00, cam marks at 12:00, no start, i replaced the coil, even though i. What should i look for?
Worse comes to worst, i'll have it towed to a mechanic shop. I doublechecked the timing on all gears and made sure they were aligned with the belt marks, used meatys timing belt video. After cranking a handful of times, it sounded like the engine was just about to start, but it wouldn't quite take.
In principle, this can affect all vehicle systems such as the fuel supply, the oil supply or the power supply.
0 Response to "Subaru Won't Start After Timing Belt Replacement"
Post a Comment